Beam and block is a very common floor for new houses in the UK, and for good reasons. It is not the right answer for every job though, and it helps to know the drawbacks before you order. This guide sets out both sides plainly: what the floor does well, where it can catch you out, and how to avoid the common problems.
At a glance
| Advantages | Disadvantages |
|---|---|
| Does not rely on the ground under it | Beams are heavy and need a lorry to reach the site |
| Quick to lay, and you can work off it once it is grouted | Made to length for your job, so it has to be ordered ahead |
| No shuttering, and no slab to pour and cure | The walls have to be built level and to the drawing first |
| A ventilated void keeps the floor clear of the ground | The void and the beams add height to the floor build-up |
| Layout drawing and calculations come with the floor | Beams can’t be cut or drilled, so changes need planning |
| Works for ground floors, upper floors and garages | Insulation, screed and any membrane are still to add on top |
The advantages of a beam and block floor
- It does not rely on the ground: the beams span from wall to wall, so the floor is carried by the foundations, not by the soil under it. That suits clay, made-up ground, sloping plots and deep fill. Approved Document C warns that a slab on more than 600mm of hardcore risks settlement and cracking, and advises a suspended floor instead.
- It is quick: once the walls are up to level, the beams are placed, the blocks dropped in and the joints grouted. There is no fill to compact across the whole floor and no slab to pour and leave to cure.
- The weather matters less: the only wet work on the deck is the grout, so a wet week does not hold the floor up in the way it can hold up a concrete pour.
- A working platform straight away: once grouted, the deck is a solid surface for the bricklayers and other trades to carry on from.
- A ventilated void: the space under the floor is vented through the outside walls. It keeps the underside of the floor clear of damp ground and helps to carry away ground gases.
- Nothing in it to rot: the floor is concrete throughout, unlike a suspended timber floor.
- The design comes with it: the beam layout drawing and structural calculations are produced for your job, ready for Building Control. See layouts and calculations.
- Good with underfloor heating: British Precast, the trade body for precast concrete, describes beam and block floors as ideal bases for underfloor heating. Our underfloor heating guide explains the build-up.
- It works upstairs too: a concrete upper floor is solid underfoot, and British Precast notes that beam and block can be used between storeys in a house when it is specified as internal floor type B in Approved Document E, the guidance on sound. See upper floors.
- Long spans: British Precast says spans of up to 8m can be achieved, depending on the load. Our span guide shows what is typical for a house.
The disadvantages of a beam and block floor
- The beams are heavy: British Precast gives typical weights of 35kg per metre for a 150mm deep beam and 68kg per metre for a 225mm one. A long beam is lifted by machine, not by hand, so think about how each beam gets from the lorry to its place.
- The lorry has to reach you: beams arrive on a lorry, with crane offload where needed. Narrow lanes, low bridges, overhead cables and tight back gardens all need thinking about first. Tell us about access when you enquire.
- It is made for your job: beams are made to length, so you can’t collect a floor off the shelf on the day you need it. Order it while the foundations are going in, not when the walls are finished.
- The walls come first, and they must be right: the beams sit on the walls, so the walls have to be built to the level and the sizes on the layout drawing. British Precast says beams need a nominal 100mm of bearing on masonry. A wall that is out of level or out of position shows up the moment the beams arrive.
- Beams can’t be altered on site: a prestressed beam must never be cut, drilled or notched by your builder. Pipes go through the blocks, and openings such as stairwells are designed in. A late change means going back to the drawing, not reaching for a saw.
- It adds height: the example in Approved Document C has a clear void of at least 150mm under the floor, and the beams sit on top of that. Your groundworker digs out to suit, and the levels need working out before the walls are built. On an extension, the finished floor also has to meet the floor of the house.
- The vents have to stay clear: the void only works if air can move through it. Vents that get buried by a new patio or blocked by soil stop it doing its job.
- It is the deck, not the finished floor: the insulation, the screed or boards, and any damp or gas membrane are still to be added on top, by your builder.
- The beams have a slight upward curve: prestressed beams are made with a camber. British Precast says allowance must be made for it in the finishes and the overall floor thickness, so your screeder needs to know.
- Heavy loads have to be planned in: a block wall built off the floor, a stone finish or a thick screed all change the design. They usually mean doubled beams or closer spacing, and they are far easier to allow for on the drawing than afterwards.
- Garages need more: British Precast says a beam and block floor in a garage should have a reinforced concrete topping designed by a competent person. See our garage floors guide.
- Little overhang: British Precast notes that floor beams have limited cantilever capacity, so a floor that sticks out past its support needs a different answer.
Common problems, and how to avoid them
Most problems with beam and block floors come from the way the job was planned or laid, not from the floor itself.
| Problem | How to avoid it |
|---|---|
| Beams don’t fit when they arrive | Build the walls to the layout drawing, and tell us before the beams are made if anything has changed on site. |
| Blocks rock or the deck feels loose | Grout the joints properly once the blocks are laid. The grout is what locks the deck together. |
| Finished floor ends up too high or too low | Add up the void, beam, insulation and screed before the walls are built to level. Tell your screeder about the camber. |
| Damp or stale air under the floor | Put the vents in two opposite outside walls as the drawing shows, and keep them clear of soil and paving for the life of the house. |
| A pipe needs to go where a beam is | Mark soil pipes, ducts and manifolds on your plans so the beams can be set out around them. |
| Extra weight added later | Tell us at the start about partitions, baths, kitchen islands and heavy finishes so they are in the calculations. |
Our installation guide goes through the laying steps and the mistakes to avoid, and the floor details guide shows the bearings, vents and service entries.
When another floor may suit you better
We supply beam and block floors, so we would rather tell you now if one is unlikely to suit.
- Good, level ground and very little fill: a ground-bearing slab can be the simpler choice. Our beam and block vs concrete slab guide compares the two fairly.
- No way in for a lorry or a lifting machine: a floor that can be carried in by hand, such as timber joists, may be the practical answer.
- A floor that has to overhang its support: ask your structural engineer what will work.
If you are not sure, send the plans anyway. We’ll say plainly whether beam and block suits the job.
Who beam and block suits best
- Self-builders: the design paperwork comes with the floor and the price is fixed. See beam and block for self-build.
- Extensions: a quick floor that leaves the ground alone and keeps the void under the house ventilated. See beam and block for extensions.
- Builders and small developers: the same floor repeated from plot to plot, with a deck to work off as soon as it is grouted.
- Difficult ground: clay, trees, slopes and deep fill, where a slab would need more work underneath it.
What happens after you send your plans
The quote form asks for your name, phone number, email, and the site address and postcode. Plans help us price the floor accurately, and you can upload them as PDF, image, DWG or ZIP files, but they are not essential.
- You send your plans. Architect’s drawings or a sketch with the inside sizes of each room. Tell us about access for the lorry and anything heavy going on the floor.
- We set out the floor. Our engineers work out the beam depth, the spacing and any doubled beams, and produce the layout drawing and the structural calculations your Building Control officer will ask for. Every floor is designed for the job it goes into.
- You get a fixed price. A clear quote for the design, beams, blocks and delivery.
- Delivered to site. Beams are made to length and delivered with the blocks, with crane offload where needed, ready for your builder to lay.
Send us your plans for a free quote or call 02475 095700.
Frequently asked questions
What are the disadvantages of a beam and block floor?
The beams are heavy and need lorry access, they are made to length so the floor has to be ordered ahead, the walls must be built level and to the drawing first, and beams can never be cut or drilled on site. The void and beams also add height, and the insulation and screed are still to add on top.
What are the advantages of a beam and block floor?
It does not rely on the ground under it, so it suits clay, slopes and deep fill. It is quick to lay with no slab to pour and cure, it gives a working platform once grouted, the void under it is ventilated, and the layout drawing and structural calculations come with the floor.
What problems do beam and block floors have?
Most problems come from planning or laying, not the floor itself: walls not built to the drawing, joints left ungrouted, floor levels not worked out in advance, blocked vents, and heavy loads added that were not in the design. Each one is avoided by following the layout drawing and telling the designer about changes.
Is a beam and block floor better than a concrete slab?
It depends on the site. Beam and block suits poor, sloping or clay ground and deep fill, and it is quicker to lay. On good, level ground with little fill, a ground-bearing slab can be the simpler choice.
Can a beam and block floor take heavy loads?
Yes, when they are designed in. Block partitions, stone finishes and thick screeds usually mean doubled beams or closer spacing. Tell us about them at the start, because every floor is designed for the job it goes into.
Is beam and block suitable for a garage floor?
Yes, with the right design. British Precast says a beam and block floor in a garage should have a reinforced concrete topping designed by a competent person. The beams are also designed for the weight of vehicles.