As a rule of thumb, a 150mm deep beam spans about 4m to 6.5m in a house, and a 225mm deep beam about 6.5m to 7.75m. The British Precast data sheet puts the upper limit for beam and block at up to 8m, depending on the load. The exact figure depends on the beam, how close together the beams sit, and what the floor has to carry.
Beam and block span table
This table shows typical maximum clear spans for standard prestressed beams with concrete infill blocks. Clear span means the distance between the faces of the walls, not the length of the beam.
| Beam | Beam spacing (centres) | Clear span, house floor (1.5 kN/m²) | Clear span, heavy use (4.0 kN/m²) |
|---|---|---|---|
| 150mm deep, narrow beam (about 125mm wide) | About 525mm | 4.1m to 4.25m | 3.35m to 3.4m |
| 150mm deep, narrow beam | About 415mm | 4.55m to 4.75m | 3.75m to 3.85m |
| 150mm deep, narrow beam | About 300mm | 5.3m to 5.4m | 4.35m to 4.45m |
| 150mm deep, wide beam (about 215mm wide) | About 615mm | 5.35m to 5.55m | 4.4m to 4.5m |
| 150mm deep, wide beam | About 505mm | 5.85m to 6.05m | 4.85m to 4.95m |
| 150mm deep, wide beam | About 390mm | 6.45m to 6.6m | 5.45m to 5.55m |
| 225mm deep beam (about 135mm wide) | About 535mm | 6.45m to 6.65m | 5.35m to 5.45m |
| 225mm deep beam | About 420mm | 7.1m to 7.35m | 5.95m to 6.1m |
| 225mm deep beam | About 310mm | About 7.75m | 6.8m to 6.95m |
The figures are a guide only. They come from the published load and span tables of large UK beam makers, which allow for finishes of about 1.5 to 1.8 kN/m², such as a screed. Each maker’s beams are different, and lighter beams span less: one published 150mm beam only 92mm wide reaches about 3.75m at 488mm spacing. The table does not allow for walls built on the floor or heavy items, which are dealt with separately on your layout.
Which beam for my room width?
Most people start with a room size, not a beam. This table turns the span table round: find the clear span between your walls and read across. It uses the lower figure in each range above, for a house floor at 1.5 kN/m², before any walls on the floor or heavy items.
| Clear span between walls | Beams that typically reach it |
|---|---|
| Up to 4m | 150mm narrow beams at wide spacing (about 525mm) |
| 4m to 4.5m | 150mm narrow beams at about 415mm |
| 4.5m to 5.25m | 150mm narrow beams at about 300mm, or 150mm wide beams at about 615mm |
| 5.25m to 5.75m | 150mm wide beams at about 505mm |
| 5.75m to 6.4m | 150mm wide beams at about 390mm, or 225mm beams at about 535mm |
| 6.4m to 7m | 225mm beams at about 420mm |
| 7m to 7.75m | 225mm beams at about 310mm |
| Over 7.75m | Beyond this table. Usually an internal load-bearing wall to split the span |
If your room sits near the top of a row, expect the next row down once a partition, a heavy finish or a different maker’s beam is allowed for. Where two options reach the same span, the choice comes down to floor depth, weight and price, and it is settled on the layout for your floor.
What decides how far a beam can span
- Beam depth and width: beams are usually 150mm or 225mm deep. Deeper and wider beams carry more over a longer distance. Our sizes and weights guide lists the typical dimensions.
- Beam spacing: moving the beams closer together shares the load between more beams, so the same beam spans further. It also means more beams and narrower gaps for the blocks.
- Imposed load: the weight of people, furniture and storage. House floors are normally designed for 1.5 kN/m². Busier or heavier uses need more, and the span drops, as the last column of the table shows.
- Finishes: a thick screed or a stone floor adds weight that the beams have to carry on top of the imposed load.
- Partitions and point loads: a wall built on the floor, a cast-iron bath or a steel post usually means doubled or trebled beams under it. See layouts and calculations for how these are checked.
Clear span, beam length and bearing
A beam has to be longer than the gap it crosses, because each end sits on the wall. British Precast gives a nominal end bearing of 100mm on masonry and 75mm on steel. So a room 4.0m wide between the walls needs beams about 4.2m long when they sit on masonry at both ends.
Beams are made to length, so measure between the walls as built where you can, and tell us if anything moves. Beams should never be cut or notched on site to make them fit. Our installation guide covers placing the beams and grouting the deck. The bearing for each beam is shown on the layout drawing, and our floor details page shows how the ends sit on the wall.
Which way do the beams run?
Beams normally run across the shorter span of the room. On a house this is usually decided by which walls can carry the load. Where a floor is too wide for one span, an internal load-bearing wall can split it in two, with beams from each side sitting on the wall. That wall needs its own foundation, so it is worth settling this before the footings go in.
Three examples
These are examples to show how the table works, not designs for your floor.
- Kitchen extension, 3.8m between the walls: inside the range of a standard 150mm beam at wide spacing. A partition or a heavy finish could still change the layout.
- New house, rooms 5m across: beyond a narrow beam at wide spacing. Expect narrow beams set close together, or wider 150mm beams.
- Open-plan self-build, 7m across: beyond any 150mm beam in the table, so a 225mm beam at closer spacing, or an internal wall to split the span.
Planning one of these? See beam and block for extensions or beam and block for self-builders.
What a longer span means for the rest of the build
- Floor depth: a 225mm beam takes 75mm more depth than a 150mm beam, which affects your void, floor levels and how the floor meets the walls.
- Weight on site: British Precast gives typical weights of 35kg per metre for a 150mm beam and 68kg per metre for a 225mm beam. A 7m beam at that weight is nearly half a tonne, so plan how it will be lifted. Tell us about access when you enquire.
- Camber: prestressed beams have a slight upward curve. One maker advises allowing span/300 in your finishes or bearing levels, which is about 13mm on a 4m span. It matters most on long spans and where beams of different lengths sit side by side.
- Cost: closer spacing and deeper beams mean more concrete. Our cost guide explains what affects the price.
Upper floors and garages
The same beams are used for upper floors, but the walls, lintels and foundations below must be checked for the extra weight. Garage floors are different: British Precast says beam and block can be used for garages where it has a reinforced concrete topping designed by a competent person. Tell us if the floor will take vehicles, because a span table for house floors will not apply. Our garage floors guide explains what changes.
What we need to work out your spans
You do not need finished drawings. Your plans, or a sketch with the inside sizes of each room, are enough to start, along with the site postcode. To set out the beams for your floor, it also helps to know:
- which walls will carry the floor, including any internal wall that could split a wide span
- any walls to be built on the floor, and heavy items such as a stone floor, a cast-iron bath or a steel post
- what the floor will be used for, and whether any part of it will take vehicles
- how you plan to insulate and finish the floor, such as a screed
- access for the delivery lorry, because long beams are heavy
Can I use a span table instead of calculations?
No. A span table helps you plan, but Building Control normally wants a beam layout and calculations for your actual floor. These are included with floors we supply, and they are worked out from the beam maker’s own data for the beams you will get. Send us your drawings and we will set out the beams, spacing and any doubled beams for you.
What happens after you send your plans
You do not need to pick a beam from the tables first. The quote form asks for your name, phone number, email, and the site address and postcode. Plans help us price the floor accurately, and you can upload them as PDF, image, DWG or ZIP files, but they are not essential.
- You send your plans. Architect’s drawings or a sketch with the inside sizes of each room. Anything that shows the walls and spans.
- We set out the floor. Our engineers work out the beam depth, the spacing and any doubled beams, and produce the layout drawing and the structural calculations your Building Control officer will ask for.
- You get a fixed price. A clear quote for the design, beams, blocks and delivery.
- Delivered to site. Beams are made to length and delivered with the blocks, with crane offload where needed, ready for your builder to lay.
Send us your plans for a free quote or call 02475 095700.
Frequently asked questions
How far can a beam and block floor span?
British Precast says spans of up to 8m can be achieved, depending on the load. In a house, 150mm deep beams typically span about 4m to 6.5m and 225mm deep beams about 6.5m to 7.75m. Your layout confirms the figure for your floor.
What size beam do I need for a 4m span?
A 4m clear span is usually within reach of a 150mm deep beam. Standard narrow beams at wide spacing reach about 4.1m to 4.25m on a house floor before partitions or heavy items, so closer spacing may be needed. Send your plans and we will set it out.
What size beam do I need for a 5m span?
A 5m clear span is beyond a standard narrow 150mm beam at wide spacing. On a house floor it usually means narrow 150mm beams set close together, at about 300mm centres, or wider 150mm beams at about 615mm centres. Walls on the floor or heavy finishes can change this, so your layout confirms it.
What size beam do I need for a 6m span?
A 6m clear span on a house floor is usually within reach of wide 150mm beams at close spacing, about 390mm centres, or 225mm deep beams at about 535mm centres. The deeper beam adds 75mm to the floor depth. Your layout confirms which suits your floor.
How much bearing does a concrete floor beam need?
British Precast gives a nominal end bearing of 100mm on masonry and 75mm on steel. Your layout drawing shows the bearing for each beam, and beams sit on a damp-proof course.
Is the span the same as the beam length?
No. The clear span is the gap between the walls. The beam is longer because each end sits on the wall, so a 4.0m clear span on masonry needs a beam of about 4.2m.
Can beam and block span further with an internal wall?
Yes. A load-bearing internal wall splits the floor into two shorter spans, with beams from each side sitting on the wall. The wall needs its own foundation, so decide this before the footings go in.
Can I cut a concrete floor beam to length on site?
No. Beams are made to length and should never be cut or notched on site to make them fit. If the walls have moved, tell us so the layout can be updated.
Can you tell me which beams I need from my plans?
Yes. Send your plans, or a sketch with the inside sizes of each room, and we will set out the beams, the spacing and any doubled beams for your floor. The layout drawing and calculations are included with floors we supply, and the quote is free.
Do I need to know which beam I need before I ask for a quote?
No. Send your plans, or a sketch with the inside sizes of each room, and the site postcode. We set out the beam depth, the spacing and any doubled beams for your floor, and the layout drawing and calculations are included.